Exploring Basic Plumbing When You Install a Bathtub
Exploring Basic Plumbing When You Install a Bathtub
Blog Article
Just about everyone seems to have their own unique rationale about Installing A Bathtub.
Installing a bath tub isn't precisely rocket science, however it does call for strong plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bath tub with a new one is also a moderately hard project. If the old tub is conveniently obtainable, the project can move easily; if you have to open a wall to eliminate the old tub and also position the new bath tub, the task is much harder. In either instance, the project is within a home handyman's abilities, although you will certainly require an assistant to move out the old tub as well as set in the new one. See to it you have actually certified on your own for the work as well as are comfortable attempting it. Rather than hiring a specialist to take control of a halfway-completed task, it is far better to think about employing one before you begin. Possibilities are you may require a specialist plumber to make tube connections.
This article will certainly help you install a new bath tub in your washroom if you have actually currently purchased a brand-new bathtub as well as do not require to change the setup of your previous water supply pipes.
Your devices and also product list should comprise the following:
Preparing for the Installment
To start with, the supporting framework supplied with the bath should be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets system to avoid stress on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you utilize every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now prepare to be suited its last placement.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water system. After doing so, activate the taps to drain any kind of water staying in the system. The procedure of getting rid of the existing faucets can be fairly bothersome because of the restricted access that is frequently the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the remaining water that will certainly originate from the pipelines. Once the supply pipelines have been removed, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming throughout this process. When the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any old securing compound.
Before going on to fit the new faucets, compare the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Utilizing both wooden boards under its feet, put the bathtub in the required position. The wooden boards are valuable in evenly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The next objective is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the tub until the spirit level checks out level.
To install faucets, fit the bottom of the outermost adaptable faucet connector to the proper supply pipeline by making a compression sign up with; after that do the exact same for the other faucet.
Activate the water supply as well as inspect all joints and new pipework for leaks as well as tighten them if required. Fill up the bathtub and likewise check the overflow outlet and the regular electrical outlet for leakages.
Finally, repair the bath paneling as described in the supplier's instruction manual. Tiling as well as securing around the tub should wait until the bath tub has actually been made use of at least once as this will settle it right into its final position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the placing opening in the bath/basin guaranteeing that the washers are in place in between the tap and also the sink. Secure the tap in place with the producer provided backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular tap connectors. The previous type must be attached to the tap ends initially, tightening just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bath satisfies the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to split a rigid seal, causing the water to penetrate the wall surface in between the bathroom and also the tiling, bring about complications with wetness and also feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your fixtures and installations. They are sold in tubes as well as cartridges, and can sealing spaces up to a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of soaked paper or soft rope. Remember to always load the bathtub with water prior to securing, to enable the movement experienced when the tub remains in use. The sealant can break fairly early if you do not consider this movement prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly available on the market. It is a good idea to fit the tiles making use of water-resistant or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that page on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing a search on the internet. If you please take a moment to distribute this post if you enjoyed it. Thank you for your time spent reading it.
Expertise? Call us! Report this page